WORLD’S FIRST TITANIUM CHASENFollow the tradition — pass on the ware.Take the 1-question survey →
Follow Studio Fungwa

Watch Magnetism: Why Your Watch Suddenly Runs Fast

Your mechanical watch kept time to a few seconds a day for years. This week it is gaining minutes. Nothing was dropped, nothing was opened, and the watch still looks and sounds normal. Before you book a service, suspect the invisible cause first: magnetism. It is the most common dramatic timing fault in modern mechanical watches, and — unusually for watch problems — it is usually fixable in seconds, without opening the case.

What magnetism does inside the movement

The timing of a mechanical watch is governed by the balance wheel and its hairspring, a fine coiled spring that expands and contracts several times a second. In a conventional movement that spring is a metal alloy. Exposed to a strong enough magnetic field, the spring itself becomes weakly magnetised, and neighbouring coils begin to attract each other.

Coils that cling together no longer contribute their full length. A shorter effective spring oscillates faster, so the watch counts time faster. That is why the classic symptom is gaining, not losing: mild cases may add tens of seconds a day, stronger cases minutes a day, and severe cases can gain far more or behave erratically as coils stick and release in different positions. Quartz watches are a different story — a strong field can disturb a quartz movement while it is present, but there is no steel hairspring to stay magnetised afterwards — and smartwatches have no hairspring at all. This article is about mechanical watches. Our quartz vs automatic guide covers how the two families differ.

The signs, in order of usefulness

Suddenness comes first. Magnetism arrives as a step change — good yesterday, fast today — often after the watch sat near a bag clasp, a phone or tablet cover, a laptop, a speaker, or a magnetic charger. Wear, dirt and failing parts usually degrade timing gradually.

Size comes second. A consistent few seconds a day is normal variation or regulation. Minutes a day, appearing suddenly, is magnetism until proven otherwise.

Erratic behaviour comes third. A magnetised watch may gain at different rates in different positions, because which coils touch changes as the watch rests dial-up, crown-down, or on your wrist. A simple regulation fault is usually more consistent.

The compass test — and its limits

Place a traditional compass flat, away from metal and electronics, and let the needle settle. Bring the watch slowly toward it, a few centimetres away, and move the watch gently. If the needle deflects as the watch approaches, the watch is carrying a magnetic field.

A phone compass app can work as a rough screen, but phones contain their own magnets and sensors vary, so a negative phone result does not clear a watch. A timing check is the backup: set the watch against a reliable time source, note the difference after 12 and 24 hours in normal wear, and compare the size and suddenness of the change with your previous rate. If you track rates as part of normal watch care — the habits are similar for mechanical pieces — a step change stands out clearly.

The fix: demagnetisation, done correctly

A demagnetiser exposes the watch to a rapidly alternating field that weakens as the watch is drawn away, scrambling the aligned magnetism in the spring until effectively none remains. Watchmakers do this with the watch on or over the device, following that device’s instructions: typically activate the field, then move the watch slowly away while the field is still on, and repeat the compass test. Technique matters more than force — pulling the watch away while the field is on is the step beginners most often miss, and a watch left sitting on an active device can end up no better, or worse.

Small mains-powered demagnetisers are widely sold online, commonly in the roughly $10 to $20 range in current buying guides, and many watchmakers will demagnetise a watch free or for a small fee. No case opening is needed, and successful demagnetisation is a complete fix, not a temporary one: magnetisation does not bend or wear the spring, so once the field is removed the spring returns to its previous behaviour. If the rate is still wrong after a verified demagnetisation — compass quiet, timing still off — then stop repeating the pass and book the service. At that point the cause is something else: a knock, dried oils, wear, or a regulation need, of the kind covered in our chronometer explainer when it discusses what a certificate can and cannot prove about a used watch.

How much field can a watch actually take?

The baseline word is “antimagnetic” under ISO 764. A watch meeting ISO 764 must withstand a direct current field of 4,800 A/m — about 60 gauss — and afterwards keep its rate within 30 seconds a day of its pre-test rate. Sixty gauss is not much at contact distance: current guides note that ordinary magnets, clasps and phone accessories can exceed it at the surface, with fields falling sharply as distance grows. The standard protects against everyday fields at a small distance, not against a watch stored directly on a magnet.

Above the baseline, makers took two routes. The older route is shielding: a soft-iron inner case acts like a cage around the movement. The famous example is the Rolex Milgauss of 1956, named for withstanding 1,000 gauss. The newer route is materials: build the escapement from parts that do not magnetise in the first place. Silicon hairsprings are the headline case — silicon cannot be magnetised — alongside non-magnetic alloys.

The modern benchmark is 15,000 gauss. Omega demonstrated a Seamaster Aqua Terra resisting more than 15,000 gauss in 2013, and the METAS Master Chronometer requirements (N001) now test cased watches at 1.5 tesla — 15,000 gauss — requiring the movement not to stop and the daily rate to stay within 0 to +5 seconds. That is 250 times the ISO 764 baseline, and far beyond any magnet most owners will meet. Most watches, however, are not Master Chronometers. Assume a conventional steel-spring movement is vulnerable until its specification says otherwise — the same habit of checking the stated rating, rather than the marketing word, that our water resistance guide teaches for depth ratings.

Keeping it from happening again

  • Distance is the whole trick. Magnetic fields fall fast with distance. A few centimetres of separation from clasps, covers, speakers and chargers does more than any storage box without magnets in its own clasp.
  • Mind the nightstand and the bag. The repeat offenders are magnetic handbag and tablet clasps, phone cases and mounts, laptop lids and speakers, and magnetic charging pucks left under a watch overnight.
  • Demagnetise first, service second. For a sudden jump to minutes a day, the cheap test order is: compass, demagnetise, retime over 24 hours. Service comes after that sequence fails.
  • Buy resistance only if your life needs it. If you work around strong magnets or simply never want to think about it, a stated high-gauss rating or a silicon hairspring is a real specification worth paying for. For most owners, distance plus an occasional demagnetisation is enough.

Go deeper with AI

This article is the starting point. Copy any of these prompts into your favorite AI assistant to learn more about watch magnetism and demagnetisers:

🔎 Diagnose a suddenly fast watch before you book a service

My mechanical watch [brand / model if known] went from about [previous rate] seconds per day to gaining about [new rate] per day, starting [when]. It was recently near [bag clasp / phone case / laptop / speaker / charger / unknown]. Walk me through the compass test, what deflection counts as positive, the correct demagnetiser technique for a typical home device, and the 24-hour timing check that confirms the fix — plus the point at which I should stop and book a watchmaker instead.

🧭 Read an antimagnetic specification honestly

Here is a watch specification: [paste the antimagnetic claim, gauss or A/m figure, and any certification named]. Convert the figure into gauss and into multiples of the ISO 764 baseline (4,800 A/m, about 60 gauss, rate within 30 seconds per day after exposure), explain whether it uses shielding or non-magnetic materials such as silicon, and compare it fairly with the METAS 15,000-gauss Master Chronometer test (0 to +5 seconds per day). Flag anything the claim does not actually promise.

💡 Build a low-magnetism storage and travel routine

I store my mechanical watch [where] and carry it in [bag / case / pocket], around [phone, laptop, tablet cover, chargers — list yours]. Audit each spot for magnetic clasps, mounts, speakers and charging magnets, rank the risks by contact distance, and give me a simple storage and travel routine that keeps a few centimetres of separation without buying specialist gear.

Tip: replace the bracketed parts with your own situation — the more specific your prompt, the more useful the answer.

The short summary

A magnetised steel hairspring clings to itself, shortens its effective length, and makes a mechanical watch run fast — suddenly, often by minutes a day, and erratically by position. A compass deflection confirms it, and a correctly used demagnetiser removes it completely in seconds, because the spring was never damaged. Protection runs from the ISO 764 baseline of about 60 gauss to soft-iron shielding at 1,000 gauss and modern non-magnetic construction tested by METAS at 15,000 gauss.

The single most important point: when a mechanical watch suddenly gains minutes a day, test and demagnetise before you pay for a service — magnetism is the likely cause, and distance from clasps, covers and chargers is the prevention.

Want better prompts, in your inbox?

One sharper AI prompt + one new watches topic every week. Free forever, unsubscribe anytime.

We never share your email. One email a week, that's the deal.